Sanding, sanding and more sanding

Following the instructions for UV SmoothPrime, I’ve laid down several coats and each one means a lot of sanding. Fortunately, it sands pretty easily and seems to do a good job filling any voids or pinholes left after the coats of micro and epoxy I applied.

The cowl after SmoothPrime

It’s a little splotchy in some spots, but it’s good enough for the high-build epoxy that’ll cover everything until paint.

SmoothPrime splotches

Bits and pieces, and the end of the pink cowl

There are a lot of gaps in the blog since February because any spare time I have has gone to building and not to blogging. So in the spirit of documenting this build in an efficient manner, I’m gonna “micro-blog” and just cover a single day’s work…so there.

The pink cowl is no more. I put on the first three coats of UV Smooth Prime with a roller and after drying for a day or so I’ll sand it down and put on the final coats.

The pink cowl…

The last of the pink cowlAnd the the white cowl…

The white cowl

 

A fair(ed) door

I finished fairing in the oil filler door. Lots of dry micro and the filler door is covered with packing tape…

Dry micro on the filler doorLots of sanding and more to go…

Sanding the filler door…and the finished product. Not perfect, but it’ll do.

Filler door sanded

I’m not dead yet

For anyone who’s following this website, I’m still alive and very much focused on the RV.  It’s just that any spare time I have (which isn’t much) is going toward working on the airplane and not toward website updates.  But just so I have something to prove to the FAA that I really am building this airplane, I’m diverting some precious building time to some updates.

Stay tuned…

Baffling, isn’t it?

Fellow RV builders know that as we closer we get to the end of our projects Van’s plans and parts become a little more “generic” – parts probably don’t fit precisely and we have to read between the lines in the instructions to figure out what needs to be done. Such is the case with the engine baffles. Van’s baffle kit is actually quite an improvement over the one they previously offered for the RV-7 but because the fit of the baffles is affected by the cowling and intake plenum/induction scoop, and because no two engines are exactly the same, quite a bit of work is required to make the baffles fit correctly.

As I write this the baffles aren’t completely installed so I’ll be adding pictures later as I finish  painting and installing them.

#4 baffle with angleWhere else should we begin but at the beginning? I started by match-drilling the aft left side baffle, and also adding a heavy 1/8″ angle to provide some additional support for the oil cooler which will later attach to it. This is a notorious weak spot in the baffle system; as designed by Van’s there’s just too much flex to support an cooler that’s full of oil and being vibrated by turbulent air and the engine. Because the angle interferes with an existing reinforcement angle (at top, with the “U” shaped notch in the middle), I added a piece of 1/8″ stock in addition to the reinforcement angle.

#3 cylinder rear baffleThe right rear baffle – behind the #4 cylinder – was a tough fit. The oil return lines are fairly close to the cylinder and getting the baffle flanges to squeeze between the cylinder and return lines was tricky.

Side and rear baffles fittedFitting the side baffles was reasonably straightforward. I had to file some material away from the valve cover cutouts to make the baffles fit around them. Not a big deal, just a bunch of iterative fit-file-repeat to get things right.

Front left baffle initial fittingThe front baffle ramps are slightly tricky. Van’s instructions call for a diagonal bend from the aft outboard corner (lower left in this pic) to the forward inboard corner (top center in this pic, right next to the starter gear) to close the gap between the ramp and lower cowl lip. This is straightforward on the right side, but the left side is more complex due to the opening that needs to be cut for the horizontal induction filter intake.

Snorkel drilled to servoHere’s the horizontal air intake “snorkel” already drilled in place to the fuel injection servo. There’s not much to this, just follow Van’s instructions. The key is to maintain a minimum 1/8″ distance between the inner snorkel surface and any nearby engine components like the starter.

Snorkel and baffle with initial cut

This is my first attempt at fitting the front left ramp; in this pic the filter is actually lying on top of the ramp – when complete, the filter’s top surface will be flush with it. I traced the filter opening on the underside of the ramp using the snorkel as a guide, then cut the opening.

Front left baffle trimmed for filter

One of the tricky aspects of this is that it’s still necessary to make the diagonal bend it the ramp that I mentioned earlier to make it fit with the cowl, while also making the ramp bend in such a way that the filter will lie snugly next to it. The filter will twist diagonally (i.e., the inboard and outboard edges won’t be parallel) so it should conform to the filter mounting brackets if the diagonal bend is made from the forward inboard corner to the aft outboard corner of the opening. I spent a fair amount of time on this after making the initial rough cut of the opening, removing lower cowl several times and adjusting the diagonal bend to get the front ramp edge positioned correctly. When necessary, I removed the snorkel and trimmed its upper edge to conform to the ramp.

It took a bit of 3D thinking to work all this out and once I had a good idea of what was supposed to happen, I ended up ordering a replacement front left baffle from Van’s. It was easier just to start over.

Sanding the filter cutoutMy friend Mike lent me his Taylor air sander for trimming the cowl and ramp. This thing is the berries – it makes short work of tasks that would ordinarily require a lot of filing and sanding. I used it to smooth rough-trimmed edges in the ramp opening and also to remove some of the lower cowl lip to accommodate the ramp’s front edge.

Baffle and filterAs you might be able to tell, I had to remove some of the lower cowl intake lip (right in front of the filter) to eliminate interference with the CB-1002A when removing and reinstalling the lower cowl. If you’re working on this area, don’t trim the cowl until you’ve determined the final cut line on the -1002A front edge.

At this point I also marked the outline of the filter flange onto the ramp for final trimming of the filter hole.

Right side corner gussetAt this point I was getting pretty burned out on the left ramp/filter/snorkel fit process so I decided to bend the CB-1009A flange and make the CB-710J conical gusset that fairs the right intake’s outboard lower corner. Van’s instructions are spot on in this area, so I don’t have much to add except to pay attention to rivet holes common between the gusset, 1009A flange and CB-710A ramp.

Snorkel mounting flanges rivetedAfter that relaxing little gusset diversion, I was ready to hit the snorkel-fitting process again. Here’s the final result – flanges with platenuts that hold the snorkel to the left air ramp assembly and also support the outer edges of the rubber air filter flange.

The instructions with Van’s “Filtered Air Box” kit are lacking in detail, so take them as advisory; what you’ll want to have at the end are three flanges that look more or less like what I have here. The rough drawings of these flanges in the instructions don’t really match what you’ll be able to do with the parts provided in the kit. Once again, you just gotta make ’em work.

One additional note – the instructions give you a method to final-trim the snorkel’s upper opening to accommodate the flanges. I had to do some trim-fit-repeat loops to make sure the flanges weren’t pushing the air ramp up and changing its fit to the cowl. I’d recommend not drilling the side flanges to the snorkel til you’re satisfied with the fit.

Fitting snorkel mounting flangesThe instructions say that it may be necessary to adjust the bend on the rear mounting flanges. Well, it’s necessary and you’ll have to make a second bend in the flange’s upper surface so that it conforms to the left air ramp as shown in the picture above.

Filter bypass hole markedOnce the flanges were fitted and drilled to the snorkel, I laid out the alternate air door hole. This accommodates the door’s flange which is riveted to the snorkel. As you can see, the mounting axes of the hole are at an angle so that when the the flange is drilled it’s at the right orientation to accommodate an actuator cable which will be installed later.

Filter bypass hole cutHere’s the flange drilled to the snorkel. Later I made up some epoxy-flax paste to fair around the flange edges and then riveted the flange into place.

Head shot of filter mountedAt this point the baffles, snorkel and filter are starting to look pretty good!

Closeup of filter mounted

In this pic I’ve fabricated the hold-down brackets which keep the filter in place; the left and right brackets are installed and there’s another one that will go across the back. You can see that the outboard bracket is actually an angle that abuts the CB-1003 cylinder baffle; I had just enough material on the -1002A ramp to accommodate the snorkel flange and bracket, which is why I recommend not trimming the ramp until you’re ready to lay out holes for the screws you see in this picture.

Making baffle trim lines

Whew…that was a lot of work. You’re seeing this in one post, but at this point I’m almost three months into the baffle-fitting process; we’re moving again so I haven’t had as much time as I’d like to devote to the project.

At this point, it’s time to trim the baffle upper edges to conform to the upper cowl (astute readers will note that there’s no post for the cowl yet – that’s on the way when the baffles are finished). I adopted Bruce Hill’s method of laying out the cut lines, which he’s documented on his website. I won’t repeat his instructions here.

#4 cylinder trim linesIn this pic the heavy blue sharpie line is the reference line laid out using Bruce’s method; it should provide a 1/2″ gap between the baffle and cowl. But this process is kinda wiggly so I’ve marked a thin blue line 1/4″ above the reference line for the initial cut.  I pulled all the baffles off the airplane and rough-trimmed to that line.

Precision gap measurement devices

The time-honored process used to mark the final trim line, used by RV builders for decades, is to use paper clips as a cheap way to measure the cowl-to-baffle gap after trimming the baffle edges. Put the clips on the baffle edges, lay the upper cowl in place and gently push it (and the paper clips) down, then remove it. After that it’s simply a matter of measuring down from the upper ends of the clips to set whatever gap you want – in my case, I went for the minimum 3/8″ gap recommended by Van’s just to reduce the chance of any air leaks later on.

In the picture above I’ve made the first cut and have placed almost 100 paper clips on the baffles and am about to cleco the top cowl in place. I don’t have any pics of the process, but after repeating the paper-clip measurement loop twice I had what I think is a nice gap along the side and rear baffles.

Fitting oil cooler reinforcementAs I mentioned before, one of the few weak parts of the baffle kit is Van’s design for the oil cooler mount. The pic above is the Van’s-supplied oil cooler brace being fitted to the baffles.

New oil filter mounting plateAdding the heavy support angle I mentioned earlier made it necessary to modify Van’s oil cooler bracket to provide a little more space on its outboard edge, otherwise the bracket’s rivet and bolt holes would be too close for comfort to the angle web. I couldn’t really make the kit-supplied bracket fit to my satisfaction, so I made another one from scratch and used the original as a template to match-drill holes for rivets and oil cooler mounting bolts.

I played with the location of this bracket a bit, trying to get it as high on the baffle as possible to maximize cooling flow while providing sufficient edge distance for the rivets that hold the whole thing together.

Here’s the final opening. As you can see, I was able to keep a fair bit of the mounting hole above the cylinder. Cooler oil temps = happy engine on hot days.

Oil cooler reinforcement trimming

Here ‘ve rough-trimmed the brace to accommodate another round of paper-clip gap measurement, and I’ve also match-drilled it to the cooler mounting bracket and support flange. You’ll see that I’ve also laid out and drilled holes for the ignition harness gasket (the figure-eight shaped hole in the center of the picture).

Oil cooler reinforcement riveting

As delivered by Van’s, the oil cooler brace’s rear mounting flange angles down, which takes away valuable space on the rear baffle that could be used to move the oil cooler higher. Taking a cue again from Bruce Hill, I cut off the original flange and used some spare  angle stock to fabricate a replacement on the brace’s upper side which picks up rivets on the mounting bracket upper edge.

Oil cooler reinforcement front flange trimmedHere’s the brace trimmed and ready for riveting. When I install the oil cooler there will be an additional stainless steel brace that attaches to the #4 cylinder’s upper valve cover screw hole and one of the inboard oil filter bolts. This should provide some additional resistance to fatigue cracking of the baffle.

Front center baffle marked for trimmimgJust when it seems the baffles are in the outbox, there’s more fitting and trimming to be done. I had previously fitted the front baffles – they surround the crankshaft – to the air ramps, but they must be fitted to the cowl in the same fashion as the side and rear baffles. If you look closely you can see blue sharpie dots where I’ve marked out initial reference lines as I did for the other baffles. A couple of measure-trim-fit-repeat cycles got them fitted to the basic curvature of the upper cowl.

Fitting upper cowl ducts

But there’s a complication. These fiberglass ramps must be fiberglassed into the upper cowl to smooth cooling airflow into the engine compartment and as is often the case for Van’s, the instructions don’t say much about how they fit. In this case, the ramps will affect the fit of side baffles for cylinders #1 and #3, so they should be in place so those baffles can be trimmed to fit.

The ramps must attach to the cowl inlet and upper surface and also have a gap between their inboard edges and the center baffles. Here I’ve removed the baffles from the engine and taped them in place to get an idea of how much to trim the inboard edges of each ramp.

Upper cowl ducts temp drilled

I tend to overthink issues like these, but in this case I just roughed out cuts on the inboard ramp edges to accommodate the center baffles, slid the ramps til they felt about right on the cowl, then drilled them into place. The cleco holes will be filled later with epoxy/flox. The left ramp (right side in this picture) didn’t fit too well along its aft edge but a little reshaping, helped by my heat gun, took care of that nicely.

Trimming front-side baffles to fit upper cowl ductOk, I think this really is the last bit of baffle fitting that needs to be done. I broke out the wooden blocks and paperclips – a couple of passes and I was done.

More to follow as I rivet the baffles together then paint and install them.

An avionics interlude

I’ve said several times before that I hate working with fiberglass. So, I took a short break and temporarily installed the G3X Touch primary flight display, G5 standby attitude/air data display, and a couple of other bits of electronics in the newly powder-coated instrument panel.

The tool that got away

Sometimes you see a really cool tool that you think about buying, but you don’t need it at the time – and when you do need it, it’s no longer available. Such is the case with the Terminal Tool.

The Terminal Tool

I had originally bought a hydraulic crimping tool from Harbor Freight, but the dies that came with it weren’t compatible with quality Amp terminals.

HF crimper result

Fortunately, a friend and fellow RV builder at KASH had a Terminal Tool. It’s easy to use, and makes first-rate crimps on large cables.

Terminal Tool

Terminal Tool crimp